Click here to download the Technical Document.

• Ethernet.
• HDMI.
• 3G/GPS.
• WiFi.

Click here to download the Technical Document.

The Ethernet Stacker Board is an add-on for the Cherry Blossom System On Module with the following features:

• An Ethernet 10/100 connection with auto MDIX
• A USB 2.0 type A port (500mA max)
• A DC-Jack for 5V power supply (2.1mm ID, 5.5mm OD)
• Dimensions – 58w x 55l x 15h

Click here to download the Technical Document.

• Effective Frame Rate – 8.7 Hz (commercial application exportable)
• Output Format – User-selectable 14-bit, 8-bit (AGC applied), or 24-bit RGB (AGC and colorization applied)
• Pixel Size – 12 μm
• Scene Dynamic Range – Low Gain Mode: -10 to 400°C; High Gain Mode: -10 to 140°C
• Spectral Range – Longwave infrared, 8 μm to 14 μm
• Temperature Compensation – Automatic. Output image independent of camera temperature.
• Thermal Sensitivity – <50 mK (0.050° C)
• Non-Operating Temperature Range – 40 °C to +80 °C
• Optimum Temperature Range – -10 °C to +80 °C
• Shock – 1500 G @ 0.4 ms
• Array format – 160 x 120, progressive scan
• FOV – Diagonal – 71°
• FOV – Horizontal – 57° (nominal)
• Power Dissipation – 150 mW (operating), 650 mW (during shutter event), 5 mW (standby)
• USB Conversion to UVC based on GroupGets Smart IO module – adapted for efficiency.
• P7 (USB) Connector Pinout:
  1. GND
  2. ID
  3. D+
  4. D-
  5. VBUS (5V) Power to module.

Click here to download the Technical Document.

• 3 x RS232 Ports (RXD and TXD only)
• 3 x RS485 Ports (Auto Tx)
• 1 x CAN Bus
• 1 x I2C Bus (3.3V levels)
• 2 x Serial Ports (3.3V Levels)
• 5-12V DC input (1.5A)
• 2 x 5V Out (regulated 500mA) and Unregulated Input Voltage out.
• 8 x optical isolated inputs.
• 8 x High side driver outputs (No overcurrent – fuse limited to 500mA total for the 8 ports).
• 2 x USB High Speed Host ports
• 1 x 10/100 Mbps Ethernet

Click here to download the Technical Document.

• Compatibility with Beaglebone Black LCD Screens.
• Supports the following Powertip LCDs available from Altron Arrow:
  – PH320240T023-IHC (320×240, 3.5″, TFT)
  – PH800480T024-IHC (800×480, 5″, TFT)
  – PH800480T013-IHC (800×480, 7″, TFT)
• Stackable design

Click here to download the Technical Document.

• Compatibility with Beaglebone Black HDMI.
• Micro HDMI connector.
• Stackable design.

Click here to download the Technical Document.

• The unit has 2 transmit and 4 receive antennas.
• Operates in the 76- to 81-GHz band with up to 4 GHz continuous chirp.
• Integrates a DSP subsystem, which contains TI’s high-performance C674x DSP for the radar signal processing.
• The device includes an ARM R4F-based processor subsystem, which is responsible for front-end configuration, control, and calibration.
• This module has Ti’s reference software with their pre-defined API pre-programmed.
• Software configurable for short range (20m) or long range (50m) operation
• 5V, 1A supply required (300mA average).
• There are 2 Asynchronous serial ports at 3.3V levels:
  – Command and control interface (115200 baud)( RS232_RX/TX)
  – Data from Radar (921600 baud)(MSS_UARTB_TX)
• Dimensions are 45mm x 45mm
• JTAG interface
• 16Mbit QSPI flash.
• 0 to 70 deg C operating.
• Stackable design.
• Connector placement with dimensions and pinout available.

Click here to download the Technical Document.

• 60 GHz Pulsed Coherent Radar (PCR)
• Measures absolute range up to 2 m (mm accurate)
• HPBW of 80 (H-plane) and 40 degrees (E-plane)
• The unit has up to 4 radar sensors to cover up to 180 degrees.
• It uses a Cortex M7 Atmel processor for the processing of radar data.
• P1 (Molex Nanofit connector for power and comms):
  1. RS485 – A
  2. RS485 – B
  3. CANH
  4. VIN (5 -12V DC)
  5. GND
  6. CANL